alternative device available sfh610a, sfh6106 www.vishay.com vishay semiconductors rev. 2.2, 23-may-13 1 document number: 83666 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, phototransistor output, high reliability, 5300 v rms description the sfh610a (dip) and sfh6106 (smd) feature a high current transfer ratio, low co upling capacitance and high isolation voltage. these couplers have a gaas infrared diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a plastic dip-4 or smd package. the coupling devices are design ed for signal transmission between two electrically separated circuits. the couplers are end-stackable with 2.54 mm spacing. creepage and clearance distances of > 8.0 mm are achieved with option 6. this version complies with iec 60950 (din vde 0805) for reinforced insulation up to an operation voltage of 400 v rms or dc. specifications subject to change. features ? good ctr linearity depending on forward current ? isolation test voltage, 5300 v rms ? high collector emitter voltage, v ceo = 70 v ? low saturation voltage ? fast switching times ? low ctr degradation ? temperature stable ? low coupling capacitance ? end stackable, 0.100" (2.54 mm) spacing ? high common mode interference immunity ? lead (pb)-free component ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 agency approvals ? ul1577, file no. e52744 system code h or j, double protection ? din en 60747-5-5 (vde 0884) available with option 1 ? csa 93751 ? bsi iec 60950; iec 60065 ? ? ? ? ? ? ? ? note ? for additional information on the availa ble options refer to option information. 1 2 4 3 e c a c sfh610a i179056 e c a c 1 2 4 3 sfh6106 ordering information part remarks sfh610a-1 ctr 40 % to 80 %, dip-4 sfh610a-2 ctr 63 % to 125 %, dip-4 sfh610a-3 ctr 100 % to 200 %, dip-4 sfh610a-4 ctr 160 % to 320 %, dip-4 sfh610a-5 ctr 250 % to 500 %, dip-4 sfh6106-1 ctr 40 % to 80 %, smd-4 sfh6106-2 ctr 63 % to 125 %, smd-4 sfh6106-3 ctr 100 % to 200 %, smd-4 sfh6106-4 ctr 160 % to 320 %, smd-4 sfh6106-5t ctr 250 % to 500 %, smd-4, tape and reel sfh610a-1x006 ctr 40 % to 80 %, dip-4 400 mil sfh610a-1x018t ctr 40 % to 80 %, smd-4 400 mil, wide leadspread sfh610a-2x006 ctr 63 % to 125 %, dip-4 400 mil sfh610a-3x006 ctr 100 % to 200 %, dip-4 400 mil sfh610a-3x007 ctr 100 % to 200 %, smd-4 sfh610a-4x006 ctr 160 % to 320 %, dip-4 400 mil
alternative device available sfh610a, sfh6106 www.vishay.com vishay semiconductors rev. 2.2, 23-may-13 2 document number: 83666 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the absolu te maximum ratings can ca use permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of th e time can adversely affect reliability. (1) refer to reflow profile for soldering conditions for surface mount ed devices (smd). refer to wave profile for soldering conditi ons for through hole devices (dip). absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input reverse voltage v r 6v dc forward current i f 60 ma surge forward current t ? 10 s i fsm 2.5 a power dissi pation p diss 100 mw output collector emitter voltage v ce 70 v emitter collector voltage v ec 7v collector current i c 50 ma t p ? 1.0 ms i c 100 ma power dissi pation p diss 150 mw coupler isolation test voltage ? between emitter and detector v iso 5300 v rms creepage distance ?? 7mm clearance distance ?? 7mm insulation thickness between ? emitter and detector ?? 0.4 mm comparative tracking index per din iec112/vde 0303 part 1 ?? 175 isolation resistance v io = 500 v, t amb = 25 c r io ?? 10 12 ? v io = 500 v, t amb = 100 c r io ?? 10 11 ? storage temperature range t stg - 55 to + 150 c ambient temperature range t amb - 55 to + 100 c soldering temperature (1) max. 10 s, dip soldering distance to seating plane ? 1.5 mm t sld 260 c electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit input forward voltage i f = 60 ma v f 1.25 1.65 v reverse current v r = 6 v i r 0.01 10 a capacitance v r = 0 v, f = 1 mhz c o 13 pf thermal resistance r thja 750 k/w output collector emitte r capacitance v ce = 5 v, f = 1 mhz c ce 5.2 pf thermal resistance r thja 500 k/w collector emitter leakage current v ce = 10 v sfh610a-1 i ceo 250na sfh6106-1 i ceo 250na sfh610a-2 i ceo 250na sfh6106-2 i ceo 250na sfh610a-3 i ceo 5 100 na sfh6106-3 i ceo 5 100 na sfh610a-4 i ceo 5 100 na sfh6106-4 i ceo 5 100 na sfh610a-5 i ceo 5 100 na sfh6106-5t i ceo 5 100 na
alternative device available sfh610a, sfh6106 www.vishay.com vishay semiconductors rev. 2.2, 23-may-13 3 document number: 83666 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? minimum and maximum values are testing requirements. typical values are characteristics of the device and are the result of en gineering evaluation. typical values are for information only and are not part of the testing requirements. coupler collector emitte r saturation voltage i f = 10 ma, i c = 2.5 ma v cesat 0.25 0.4 v coupling capaci tance f = 1 mhz c c 0.4 pf current transfer ratio parameter test condition part symbol min. typ. max. unit i c /i f i f = 10 ma, v ce = 5.0 v sfh610a-1 ctr 40 80 % sfh6106-1 ctr 40 80 % sfh610a-2 ctr 63 125 % sfh6106-2 ctr 63 125 % sfh610a-3 ctr 100 200 % sfh6106-3 ctr 100 200 % sfh610a-4 ctr 160 320 % sfh6106-4 ctr 160 320 % sfh610a-5 ctr 250 500 % sfh6106-5t ctr 250 500 % i f = 1 ma, v ce = 5 v sfh610a-1 ctr 13 30 % sfh6106-1 ctr 13 30 % sfh610a-2 ctr 22 45 % sfh6106-2 ctr 22 45 % sfh610a-3 ctr 34 70 % sfh6106-3 ctr 34 70 % sfh610a-4 ctr 56 90 % sfh6106-4 ctr 56 90 % switching char acteristics parameter test condition part symbol min. typ. max. unit non-saturated current v cc = 5 v, r l = 75 ? i f 10 ma rise time v cc = 5 v, r l = 75 ? t r 2s fall time v cc = 5 v, r l = 75 ? t f 2s turn-on time v cc = 5 v, r l = 75 ? t on 3s turn-off time v cc = 5 v, r l = 75 ? t off 2.3 s cut-off frequency v cc = 5 v f co 250 khz saturated current sfh610a-1 i f 20 ma sfh6106-1 sfh610a-2 i f 10 ma sfh6106-2 sfh610a-3 i f 10 ma sfh6106-3 sfh610a-4 i f 5ma sfh6106-4 electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit
alternative device available sfh610a, sfh6106 www.vishay.com vishay semiconductors rev. 2.2, 23-may-13 4 document number: 83666 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? all values presented are typical values. saturated rise time sfh610a-1 t r 2s sfh6106-1 sfh610a-2 t r 3s sfh6106-2 sfh610a-3 t r 3s sfh6106-3 sfh610a-4 t r 4s sfh6106-4 fall time sfh610a-1 t f 11 s sfh6106-1 sfh610a-2 t f 14 s sfh6106-2 sfh610a-3 t f 14 s sfh6106-3 sfh610a-4 t f 15 s sfh6106-4 turn-on time sfh610a-1 t on 3s sfh6106-1 sfh610a-2 t on 4.2 s sfh6106-2 sfh610a-3 t on 4.2 s sfh6106-3 sfh610a-4 t on 6s sfh6106-4 turn-off time sfh610a-1 t off 18 s sfh6106-1 sfh610a-2 t off 23 s sfh6106-2 sfh610a-3 t off 23 s sfh6106-3 sfh610a-4 t off 25 s sfh6106-4 switching char acteristics parameter test condition part symbol min. typ. max. unit
alternative device available sfh610a, sfh6106 www.vishay.com vishay semiconductors rev. 2.2, 23-may-13 5 document number: 83666 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? as per iec 60747-5-2, 7.4.3.8.1, this opto coupler is suitable for "saf e electrical insulation" only within the safety rating s. compliance with the safety ratings shall be ensured by means of protective circuits. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - linear operatio n (without saturation) fig. 2 - current transfer ratio (ctr) vs. temperature fig. 3 - switching operation (with saturation) fig. 4 - output characteristic s (typ.) collector current vs. collector emitter voltage safety and insulatio ratings parameter test condition symbol min. typ. max. unit climatic classification (according to iec 68 part 1) 55/100/21 comparative tracking index cti 175 399 v iotm 10000 v v iorm 890 v p so 400 mw i si 275 ma t si 175 c creepage distance standard dip-4 7 mm clearance distance standard dip-4 7 mm creepage distance 400 mil dip-4 8 mm clearance distance 400 mil dip-4 8 mm insulation thickness, ? reinforced rated per iec 60950 2.10.5.1 0.4 mm isfh610a_01 r = 75 l v cc =5v i c 47 i f % 10 3 5 10 2 10 1 - 25 75 25 050 5 t a (c) isfh610a_03 i f = 10 ma, v cc = 5.0 v 1 2 3 4 i c i f isfh610a_02 1. 0 k v cc =5v 47 i f ma 30 10 20 0 015 10 5v i c v ce isfh610a_04 i f = 14 ma i f = 12 ma i f = 10 ma i f = 6 ma i f = 8 ma i f = 4 ma i f = 2 ma i f = 1 ma
alternative device available sfh610a, sfh6106 www.vishay.com vishay semiconductors rev. 2.2, 23-may-13 6 document number: 83666 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 5 - diode forward voltage vs. forward current fig. 6 - transistor capacitance (typ.) vs. collector emitter voltage fig. 7 - permissible pulse handlin g capability forw ard current vs. pulse width fig. 8 - permissible power dissipation vs. temperature fig. 9 - permissible diode forward current vs. ambient temperature 1.2 v 1.1 1.0 0.9 10 -1 10 1 10 2 5 ma 55 10 0 v f i f isfh610a_05 v f = f (i f ) 25 ? 50 ? 75 ? 0 5 10 15 20 pf 10 -2 10 -1 10 0 10 1 10 2 v c v e isfh610a_06 f = 1.0 mhz c ce ma 5 5 10 1 5 10 2 10 3 10 4 10 -5 10 -4 10 -3 10 -2 10 -1 10 0 10 1 s i f t p isfh610a_07 t p i f t t d = t p d = 0 0.005 0.01 0.02 pulse cycle d = parameter t p i f 0.05 0.1 0.2 0.5 dc ma 0 30 60 90 120 0 50 100 75 25 ? i f t a isfh610a_08 p tot = f (t a ) mw 0 50 100 150 200 0 50 100 75 25 ? p tot t a isfh610a_09 transistor diode
alternative device available sfh610a, sfh6106 www.vishay.com vishay semiconductors rev. 2.2, 23-may-13 7 document number: 83666 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in inches (millimeters) 0.74 2.41 1.22 0.25 typ. 2.79 pin 1 identification i178027-1 6.48 6.81 4.55 4.83 0.76 1.14 4 typ . 2.67 3.30 3.81 0.51 0.89 10 0 to 15 1.32 0.84 3.30 6.35 5.84) is om ethod a 7.62 typ. i17802 9-2 0.255 (6.48) 0.268 (6.81) 0.179 (4.55) 0.190 (4.83) 0.030 (0.76) 0.045 (1.14) 4 typ. 0.052 (1.32) 10 lead coplanarity 0.004 (0.102) max. (?k?) smd iso method a 0.100 (2.54) r 0.010 (0.25) 0.070 (1.78) 0.030 (0.76) 0.315 (8.00) mi n. 0.060 (1.52) 0.435 (11.05) 0.048 (1.22) 0.105 (2.67) 0.095 (2.41) 0.033 (0.84) 0.029 (0.74) 0.150 (3.81) 0.130 (3.30) 0.098 (0.249) 0.040 (0.102) 0.010 (0.25) 0.008 (0.20) 0.296 (7.52) 0.395 (10.03) 0.375 (9.53) pin 1 identification 0.312 (7.92)
alternative device available sfh610a, sfh6106 www.vishay.com vishay semiconductors rev. 2.2, 23-may-13 8 document number: 83666 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 0.014 (0.35) 0.010 (0.25) 0.400 (10.16) 0.430 (10.92) 0.307 (7.8) 0.291 (7.4) 0.407 (10.36) 0.391 (9.96) option 6 0.315 (8.0) min. 0.300 (7.62) typ. 0.180 (4.6) 0.160 (4.1) 0.331 (8.4) min. 0.406 (10.3) max. 0.028 (0.7) option 7 18487 0.300 (7.62) typ. 0.150 (3.81) 0.130 (3.30) 0.472 (12.00) max. 0.365 (9.27) min. 0.020 (0.50) 0.000 (0.00) option 8
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
